Menu
Domestic Services
Commercial Services
cherry picker hire
Contact Us
Arrays close to busy routes collect a soiling layer with a different character from those in quieter positions, and it is harder to remove. Combustion produces very fine carbon and hydrocarbon particulate, along with brake and tyre material, and all of it settles as a thin greasy film rather than a dry dust. That film matters for two reasons. It is sticky enough to resist rainfall almost entirely, so it accumulates continuously rather than being periodically rinsed away. And it acts as a binder, holding mineral dust and pollen onto the glass that would otherwise blow off or wash away on their own. The result is a consolidated layer that builds faster and adheres better than the equivalent on a rural property, and it is largely invisible until a section of glass is cleaned beside a section that has not been. Removing it depends on the water rather than on effort. Filtration and deionising resin strip the dissolved solids out until the reading approaches zero, and water in that state behaves as an active solvent, pulling material into solution instead of running over it. Applied through a soft filament brush on a telescopic pole and given time to work, it lifts the greasy film without any detergent being required — which matters, since surfactants leave their own residue on the anti-reflective coating and attract the next layer faster. Pressure stays low throughout, nothing abrasive touches the coating, nothing is directed at frame seals or junction boxes, and no weight goes onto a module. Properties in March near heavily used routes usually justify a shorter solar panel cleaning interval than the general recommendation.
A greasy film is the test of whether a contractor’s water is doing what it should. Mineral dust will come off with almost anything. Combustion residue will not, and an array cleaned with tap water and a general-purpose brush frequently looks better without performing much better, because the film has been smeared rather than lifted and minerals have dried on top of it. Doing it properly means purified water on every job, produced through filtration and deionising resin rather than drawn from a tap, with output monitored rather than assumed — spent resin produces water that spots, and that is usually noticed a day later, by which time nobody connects the two. It also means giving the surface time. Bonded film releases with dwell rather than with force, so the array is wetted first and worked afterwards. The rest of the standard is unchanging. Soft filament brush heads. Low pressure, with nothing directed at frame seals, flashings or junction boxes. No operative putting weight on a module at any point. Full coverage of every panel including the frame line and lower edges rather than only the glass that shows from the ground. Public liability insurance and a risk assessment matched to the actual height and configuration sit behind every visit, and work is rescheduled rather than forced when wind or frost makes a long pole unsafe. Photographs follow afterwards showing the array before and after. Residents in March comparing solar panel cleaning services should ask specifically what the water is passed through before it reaches the glass. It is a short question and the answer separates the trade quite effectively.
Arrays carrying a heavy combustion film are not priced differently in principle, but they do take longer, and the reason is dwell time rather than difficulty. The layer releases once purified water has had a chance to work on it, and rushing that stage produces a smeared result that satisfies nobody. The figure otherwise follows the standard inputs. Module count is charged per panel, with the rate improving as arrays grow, because travel, unloading, assembling poles and producing purified water are fixed costs incurred once regardless of how much glass follows them. That fixed portion is why a minimum charge applies and why a small array never costs proportionally little. Reach adjusts it next. An accessible elevation with firm level standing and clear room to extend a pole is the least expensive arrangement, while unusual height, restricted ground or obstructions between the operative and the wall all lengthen the job. Where hired access equipment is genuinely required it appears as a separate stated item rather than being folded into the rate. Condition supplies the third input, and on a system that has been accumulating film for several years without attention it is usually the largest of the three. Frequency is the practical lever. A shorter interval keeps the layer from consolidating, which makes each visit quicker and cheaper than an occasional heavy clean. Assessments for properties in March are free and carry no obligation, repeat bookings sit below one-off rates, and the quoted figure covers the complete array including frames and lower edges, purified water throughout and photographs afterwards, with nothing appearing as an extra once the work is done.
Remove years of dirt, grime, algae and staining for a cleaner, fresher finish.
Professional techniques designed to protect your surfaces while delivering outstanding results.
Keep your property looking its best with regular solar panel cleaning.
Professional solar panel cleaning in March offers a simple and effective way to maintain the cleanliness, appearance and performance of your solar panels. Over time, dirt, dust, bird droppings, pollen, leaves, algae and other environmental debris can accumulate across the surface of solar panels, leaving them looking dirty and potentially reducing the amount of sunlight reaching the panels. Regular solar panel cleaning helps remove this unwanted build-up, keeping the panels cleaner and allowing them to receive as much available sunlight as possible. Keeping solar panels clean can also support ongoing maintenance by making it easier to identify visible issues, damage or areas that may require further attention. Professionally cleaned solar panels can improve the overall appearance of your property while helping you get the most from your solar installation. Using suitable cleaning methods and equipment for solar panel surfaces is important to achieve effective results while reducing the risk of scratching, marking or damaging the panels. Whether your solar panels have accumulated bird mess, dust, dirt, pollen, algae or general environmental grime, professional solar panel cleaning in March can help keep them cleaner, clearer and better maintained throughout the year.
Commercial premises close to main routes, distribution yards or busy loading areas accumulate combustion film faster than almost any other category of site, and on a large installation that translates into a measurable and continuous loss. Vehicle movements on the premises contribute as much as passing traffic, particularly where engines idle near a building carrying an array above. Pro Clean Xtreme approaches those sites as documented, scheduled work. A survey establishes module count, mounting arrangement, structural condition and fragility, edge protection and the safest route to every row, producing a site-specific risk assessment and method statement agreed with the responsible person before dates are confirmed. Access is specified for the building: ground-level pole work where reach permits, mobile elevating work platforms or rope access where it does not, with operatives qualified for the method. The cleaning relies on purified water supplied from tanks brought to site, applied at low pressure through soft brushes and given dwell time on the bonded film, with frames and lower edges included alongside the glass. No detergent or solvent is used at any stage, which keeps drainage unaffected and removes any substance from the site’s own reporting. Attendance is arranged around the operation, including weekends and out-of-hours, with large arrays phased where continuous access is impractical. Dated photographs and a written completion record follow every visit. Operators around March generally find commercial solar panel cleaning needs a shorter interval than the average, and the generation data either side of the first clean tends to make the case without further argument once a full quarter of figures is available.
Founded in 2016 by Karl Crofts, Pro Clean Xtreme has grown from a dedicated one-man operation into a trusted family-run team. Joined by his wife Lindsay and family members Callum and Rachel, we pride ourselves on delivering professional, safety-first cleaning. By combining honest communication with continuous investment in the industry’s best low-pressure steam equipment and safe access systems, we deliver exceptional results for every residential, commercial, and industrial client.
Founded by Karl Crofts, delivering reliable local service for over a decade.
Our own tracked cherry picker provides safe access without walking on tiles.
Safe low-pressure steam cleaning, softwashing, and specialist pre-solar preparation.
Ten years of trusted, family-run service delivering high-quality workmanship on every project.
As a family-run business established in 2016, we have developed a trusted reputation across March for reliable, professional solar panel cleaning. We combine years of experience with specialist cleaning equipment and careful working practices to provide a thorough service for residential and commercial solar installations. Our approach is straightforward and transparent, with every job completed with attention to detail and the condition of the panels in mind. From removing built-up dirt and bird deposits to clearing pollen, dust and other surface debris, we work carefully to leave solar panels clean and clear. Fully insured and committed to high standards of workmanship, we provide a dependable solar panel cleaning service from initial assessment through to completion.
We take immense pride in the reputation we have built across Cambridgeshire and the surrounding areas since 2016. As a family-run business, delivering exceptional customer service, honest communication, and high-quality workmanship is at the heart of everything we do. Read through our latest Google reviews to see why residential homeowners, housing associations, and commercial contractors consistently trust Pro Clean Xtreme to safely protect and restore their properties.
Here are the answers to some of the most frequently asked questions about our solar panel cleaning services. If you have a question about your solar panels, a specific cleaning requirement, or need further information about our service, please get in touch with our experienced team. We are always happy to provide advice and help you find the right solution for keeping your solar panels clean and well maintained.
The ideal frequency depends on your location, surroundings and how quickly dirt and debris build up. For many properties, an annual clean can help keep panels clear and well maintained.
Yes, keeping panels free from dirt, bird droppings, dust, pollen and other debris allows more sunlight to reach the surface. Cleaning can therefore help your panels operate as efficiently as possible.
Solar panels can collect bird droppings, dust, pollen, leaves, algae, grime and other environmental debris. These deposits can build up over time and affect the cleanliness of the panel surface.
Yes. Professional solar panel cleaning can be carried out on a wide range of domestic and commercial properties, subject to suitable access and safe working conditions.
Professional solar panel cleaning should be carried out using appropriate equipment and techniques designed for solar panel surfaces. Careful cleaning helps remove deposits without unnecessarily damaging or scratching the panels.
Rain can wash away some loose dirt, but it does not necessarily remove stubborn bird droppings, pollen, grime and other deposits. Regular professional cleaning can provide a more thorough clean than rainfall alone.
Yes, we provide professional solar panel cleaning in March, helping domestic and commercial customers keep their solar panels clean, clear and properly maintained.
Getting an initial estimate for your property is completely effortless. Simply fill out the form below with your full property address, and our family-run team will utilise Google Earth before providing a quotation. Whether you are a homeowner, a housing association, or an installation company preparing a site, let us know your specific requirements and we will get back to you promptly with an initial assessment.
